The ring die  and also  journalism roller of the biomass pellet making machine rotate at a  consistent  rate, and the working state of each instant is  generally the  very same. If the amount of feed material is unchanged, the energy  usage should also be  fairly  steady, and the  existing will be reflected on the motor. Also  reasonably stable.

Related post: biomass pellet machine price

When the biomass pellet making  maker  equipment is working, we adjust the feeding amount as long as the material thickness in the feeding  location is less than the  optimum starting point of  journalism  location, it will  straight affect the  size of the  efficient  workplace of the pressing  location  and also the pressing  location,  as well as cause the  present to flow.

The  change  as well as the  modification of the hourly  result of the biomass pellet making  maker,  and also if the  density of the  product layer in the feeding  location is  higher than the  optimum starting point of  journalism area, in addition to increasing the  density of the material layer in the feeding  location, it will not  impact the hourly output and energy  intake per unit time.

Related post: biomass pellet plants

If there is  any kind of  influence, it will no longer cause  adjustments in  present and biomass pellet making machine  result.  Due to the fact that the  density of the  product layer in the feeding zone exceeds the  optimum  beginning point of  journalism zone, the interval  in between  journalism zone  and also  journalism zone is constant  with no change. In the interval where the multi-feed  product  lies, the  securing angle is  more than the  crucial  rubbing angle, and the material will not be  pressed into the pressing  location.

 By doing this, with the increase of the feeding  quantity of the biomass pellet making  equipment, the balance of in and out is  damaged,  as well as the in is  higher than the out,  as well as the material layer in the feeding  location is It will accumulate thicker and thicker  up until all the  voids are filled and blocked to the feed port,  to make sure that the biomass pellet  maker can not  function  usually.  Currently, the current will increase.

Related post: https://www.pellet-richi.com/wood-pellet-machine/biomass-pellet-mill.html

In the  real  job of the biomass pellet making  maker, with the  modification of the feeding  quantity, the  instant output  as well as the current of the  major  electric motor will  transform accordingly.  As well as when the feeding  density does not exceed the maximum  beginning point of the pressing area, it  will certainly not cause  a growing number of material layers in the feeding area  as a result of the  rise in the amount of powder we feed.

As has been said  prior to, the area that can  trigger instantaneous output and  power  intake  modifications  need to be  both  locations of work  as well as material layers - the compression  location  as well as the biomass pellet  device extrusion area, so we  assume that the third  location mentioned  over- - The  affordable existence of the feeding  location has certain  problems.

That is to say, the fed material layer is  dispersed in the compaction  location, the extrusion  location  and also the feeding area whose total thickness does not exceed the maximum  entrance point of the compaction area.

Related post: 10T/H Wood Pellet Plant For Sale United States 

The biomass pellet making  equipment  will certainly  function  generally under the allowable power. If the amount is  as well  big  and also exceeds the  density of the maximum starting point of the compaction area, the material layer  will certainly  gather  and also  slowly  boost,  and also the biomass pellet making  maker will not work normally.  Existing is fluctuating.

 With the above  evaluation, let's  talk about some  sensations exhibited by the biomass pellet making  device under two possible working conditions:

( 1 )When the power of the main  electric motor is not large  sufficient compared with the corresponding biomass pellet making  device granulation  criteria, the  density of our feed is at the end of the extrusion  area  and also the  optimum  entrance point of the compression  area (this will vary with the raw  products, compression  proportion,  reliable length-diameter ratio,  moisture,  stress rollers  and also  various other variable  aspects to  change  as necessary),  usually will not exceed the maximum  beginning  factor, with the increase of the feeding  quantity, the compression  location  will certainly  transform  appropriately.

Related post: straw pellet mill

The  size of the interval will be shortened,  and also the interval length of the  press  location will  slowly  enhance accordingly,  as well as the current of the  primary motor  will certainly  additionally gradually  enhance  up until it reaches the  optimum  allowed  usage. If the  existing reaches the  defense  worth we set, and the thickness of the feeding  product has not exceeded the thickness of the  optimum starting point of the biomass pellet  device pressing area, if the feeding amount is  enhanced, the safety system will act, and the excess powder will be discharged. In order to ensure the  regular function of biomass pellets.

( 2 ) Intend the power of the main  electric motor is  huge or the  electric motor  falls short to overload after the thickness of the feeding material  goes beyond the thickness of the maximum  beginning  factor of the pressing  location  because of the  detailed  modifications of  lots of variables. At this time, the powder fed to  individuals can not increase the time  result, nor will it  create the  boost of the  major motor  existing, but can only continue to  raise the powder pile  gathered in the machine  up until the  internal cavity of the biomass pellet press  device is blocked.

Related post: Peanut Shell Pellet Machine

 Trigger the biomass pellet making  equipment to not  function  effectively.  Naturally, this special phenomenon  hardly ever  happens in  real production (if the raw material moisture is  as well  huge, the effective  facet  proportion is  also small, the  stress roller is  significantly worn  as well as the gap is not  changed  appropriately, the raw material is  changed,  and so on, this phenomenon may occur), this is our undesired  problems.

 Comprehensive  evaluation of the  initial  frequently  made use of  functioning state, it is  simple to  recognize that on the  facility that the  pertinent conditions are  the same, with the  adjustment of the feeding amount, the interval  size of the compression zone  and also the extrusion zone is within a certain  variety  Matching changes are  additionally made (the feed flow  price is reduced, the  size of the extrusion  area is  decreased,  and also the length of the compression  area is  lengthened; otherwise, the extrusion  area is  prolonged  as well as the compression zone is  reduced),  and also the feeding  quantity does not  surpass the pressure. When the thickness of the maximum starting point of the tight area is concerned, the lengths of the above two intervals are not a constant value when this article is written. The larger the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.

Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.

RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!

For details please contact: Richi Machinery 

WhatsApp：86 138 3838 9622
Email：enquiry@pellet-richi.com